Submersible pump, suitable for pumping clean water. Vertical or horizontal installation. Components are made of stainless steel, EN 1.4301 (AISI 304), for high corrosion resistance. Approved for the supply of drinking water. Equipped with a 5.5 kW 5.5 kW MS6000 motor with waterproofing by anti-sand protection, mechanical seals, water lubrication of the bearings and a volume compensation membrane. The motor is wet rotor and offers good mechanical stability and high efficiency. Equipped with a Grundfos Tempcon sensor combining electrical communications and an MP204 control panel, allows temperature control.

APPLICATIONS

• Leach mining
• Ground water intake

Submersible pump, suitable for pumping clean water. Vertical or horizontal installation. Components are made of stainless steel, EN 1.4301 (AISI 304), for high corrosion resistance. Approved for the supply of drinking water. Equipped with a 5.5 kW 5.5 kW MS6000 motor with waterproofing by anti-sand protection, mechanical seals, water lubrication of the bearings and a volume compensation membrane. The motor is wet rotor and offers good mechanical stability and high efficiency. Equipped with a Grundfos Tempcon sensor combining electrical communications and an MP204 control panel, allows temperature control.

APPLICATIONS

• Leach mining
• Ground water intake

Renewable energy submersible pumps with build in inverter for solar, wind and AC powersource. Runs on both AC and DC voltage.

APPLICATIONS

• Solar water solutions
• Community water supply
• Livestock watering
• Solar boosting and water supply solutions

Submersible borehole pumps designed for pumping groundwater.

• Submersible pump, suitable for pumping clean water.
• Vertical or horizontal installation.
• Components are made of stainless steel, EN 1.4301 (AISI 304), for high corrosion resistance.
• Approved for the supply of drinking water.
• Equipped with a 0.55 kW MS402 motor with lip seal and anti-sand protection, water lubrication of the bearings and a volume compensation membrane.
• The motor is wet rotor and offers good mechanical stability and high efficiency.

APPLICATIONS

• Applications
  • Groundwater supply to waterworks
  • Irrigation in horticulture and agriculture
  • Groundwater lowering
  • Pressure boosting
  • Industrial applications
  • Fountains
  • Mining
  • Offshore.

DESCRIPTION

• Discharge sizes from 2-3 inches and horsepower ranges from 1-7.5 hp.
• Lightweight and compact.
• Durable construction provides low maintenance and easy repair.
• Internal thermal motor protection, dual silicon carbide mechanical seals.

DESCRIPTION

• Discharge sizes from 2-6 inches and horsepower range from 2-15 hp.
• Utilizes 2-pole, 3600 rpm motors to achieve higher heads.
• High pressure rated mechanical seals are isolated to provide superior motor protection.
• Rugged cast iron construction.
• Pressure relief ports and exclusive oil lifter extend mechanical seal life, eliminating premature wear and failure in high head operations.
• Internal thermal motor protection.
• Anti-wicking cable entrance.

DESCRIPTION

• Discharge sizes from 3-14 inches and horsepower ranges from 3-50 hp.
• KRS2-80, KRS2-100, KRS2-150, and KRS-200 are agitator pumps that are ideal for quarry and gravel pit drainage.
• 4 pole, 1800 rpm motors reduce impeller tip speed and extend parts wear life
• Rugged cast iron construction holds up to the most aggressive mining, aggregate, construction applications.
• Dual Silicon Carbide Mechanical seals in a separate oil bath.

The pump is built in stainless steel and resists corrosion even in more aggressive environments thanks to the ZR8 version in Duplex.

This design feature boasts a “dynamic” wear ring which reduces hydraulic losses to a minimum and prevents the pump from blocking during stand-by periods. Meaning the pump is ideal for use in mining, water supply from deep wells and pressure boosting and water distribution applications in municipal and industrial systems.

Z8: AISI 304
ZR8: DUPLEX

All Z8, ZR8 pumps can be coupled to NEMA standard motors.

The head and motor support of this lightweight and sturdy pump is cast in stainless steel as are the shaft sleeves ensuring long lasting reliability and efficiency.

The pump has a high sand handling capability which make the Z6-ZN6 series suitable for use in aggressive environments such as water supply from deep wells or irrigation over large areas such as golf courses.

Z6: AISI 304
ZN6: AISI 316

All Z6-ZN6 pumps can be coupled to NEMA standard motors.

PRODUCT FEATURES

• Sturdy design with casted discharge head and motor support
• Avialable in AISI 304 or AISI 316
• Delivery up to: 78 m³/h
• Head up to: 700 m
• Max immersion depth: 350 m

The range is designed to give high efficiency throughout its performance area and almost every duty point between 120 m3/h and 460 m3/h has an efficiency higher than 80%.

The shaft alignment of the pump is specifically designed to reduce vibration issues throughout the lifetime of the pump. The wear ring on the Z10/ZR10 pump also keeps recirculation losses to a minimum, ensuring high levels of efficiency in applications such as supply of surge tanks and reservoirs, fire fighting and agricultural flood irrigation.

Z10-Z12: AISI 304
ZR10-ZR12: DUPLEX

All Z-ZR10-Z-ZR12 pumps can be coupled to NEMA standard motors.